RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: Bax
Showing results 1 to 15 of 15
Search took 0.17 seconds.
Forum: Glow Engines
08-17-2017, 06:54 AM
Replies: 988
Views: 180,852
Posted By Bax

Here are the stock numbers and list prices of the...

Here are the stock numbers and list prices of the parts you asked about:

OSMG2672 72108110 FLX PIP FS70-91 240MM US$49.99
OSMG2684 72108100 FLX PIP FS70-91 120MM US$37.99...
Forum: Glow Engines
03-13-2017, 07:16 AM
Replies: 988
Views: 180,852
Posted By Bax

The O.S. FL-70 was a non-ringed four-stroke...

The O.S. FL-70 was a non-ringed four-stroke engine, but did have a ball-bearing-supported crankshaft. O.S. did not make a bushing four-stroke engine. Even the old FS-75 used ball bearings.
Forum: Glow Engines
09-04-2015, 04:33 AM
Replies: 988
Views: 180,852
Posted By Bax

We have no idea what the material is. We never...

We have no idea what the material is. We never disassembled the pumps, since they were not repairable by anyone other than the factory. Some pumps could not be disassembled without destroying them.
Forum: Glow Engines
09-01-2015, 07:13 AM
Replies: 988
Views: 180,852
Posted By Bax

Try running it for several tanks' worth of fuel...

Try running it for several tanks' worth of fuel to see if the pump/regulator system needs to loosened up. They can get dry and not regulate properly. The only other solution is to replace the...
Forum: Glow Engines
08-31-2015, 06:28 AM
Replies: 988
Views: 180,852
Posted By Bax

You may have a problem with the pump/regulator...

You may have a problem with the pump/regulator system, especially if it's a few years old and has been run infrequently.
Forum: Glow Engines
08-26-2015, 06:56 AM
Replies: 988
Views: 180,852
Posted By Bax

A 14x7 three-blade prop is a LOT of propeller for...

A 14x7 three-blade prop is a LOT of propeller for that engine. We'd use a 14 x 7 two-blade or a 13 x 8 two blade. For a 3-blade prop, we'd use a 12 x 6 or 7. You want the engine to turn around...
Forum: Glow Engines
08-25-2015, 07:38 AM
Replies: 988
Views: 180,852
Posted By Bax

Glow engines can all be problematic when trying...

Glow engines can all be problematic when trying to run them inverted. That's because the glow plug becomes the lowest point in the fuel system. When the throttle is closed to idle, liquid fuel can...
Forum: Glow Engines
08-24-2015, 06:00 AM
Replies: 988
Views: 180,852
Posted By Bax

The O.S. FS-120 Surpass II has the C-13...

The O.S. FS-120 Surpass II has the C-13 carburetor with a velocity stack. The original series FS-120 Surpass has the pump with the large brass screw in the center and no velocity stack on the carb....
Forum: Glow Engines
12-02-2013, 07:32 AM
Replies: 988
Views: 180,852
Posted By Bax

You might mean an O.S. Max .90 FSR. There never...

You might mean an O.S. Max .90 FSR. There never was an O.S. Max .90 SF. The .90 FSR came out in 1978. If you have a more recent engine, then it will be a .91 FSR or a .91 FX.
Forum: Glow Engines
05-04-2010, 08:57 AM
Replies: 988
Views: 180,852
Posted By Bax

RE: OS engines users Club

Just an aside. For those who collect silver, or have good silver, don't use regular silver "polish". It will remove the patina good silver is supposed to develop. Check with a quality silver...
Forum: Glow Engines
11-17-2009, 09:43 AM
Replies: 988
Views: 180,852
Posted By Bax

RE: OS engines users Club

The O.S. Max .65LA has not been discontinued. It is readily available.

OSMG0066 16512 65LA NON-RING 60J E4010 US$199.99

However, a 10 x 6 propeller would be considered much too...
Forum: Glow Engines
10-03-2008, 09:33 AM
Replies: 988
Views: 180,852
Posted By Bax

RE: OS engines users Club

Do you mean the O.S. Max .55 AX or the O.S. FS-a56? O.S. doesn't have a ".56 ATX" engine.
Forum: Glow Engines
09-19-2008, 09:16 AM
Replies: 988
Views: 180,852
Posted By Bax

RE: OS engines users Club

That a good RPM for that engine. That engine runs best when propped to run in the high-11,000's.
Forum: Glow Engines
09-11-2008, 09:18 AM
Replies: 988
Views: 180,852
Posted By Bax

RE: OS engines users Club

There never was an O.S. Max 1.20 FX engine.
Forum: Glow Engines
08-13-2008, 09:43 AM
Replies: 988
Views: 180,852
Posted By Bax

RE: OS engines users Club

It sounds like your engine is going lean and overheating. That could be caused by a variety of reasons. If your engine has the needle valve housing molded as part of the rear cover, an update was...
Showing results 1 to 15 of 15


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.